| Previous | Next |
| TAPI_E_PHONENOTOPEN | TAPI_E_WRONGEVENT |
TAPI_E_CALLNOTSELECTED
The specified call is not currently selected
TAPI_E_CALLNOTSELECTED is HRESULT 2147745876 (0X80040054) from Tapi3err.h. AllStat describes it as “The specified call is not currently selected.” The result normally appears while requesting information or control that applies only to a call currently selected in a phone or UI context. Its useful interpretation is precise: the selected call is not valid for the exact provider, object, method, or lifecycle state that consumed it.
Typical call path
- This result belongs to TAPI 3 address, call-control, phone, terminal, media-provider, request, or call-center processing.
- Associate this result with one concrete native method among ITTAPI, ITAddress, ITBasicCallControl, ITCallInfo, ITStream, ITTerminal, ITPhone, provider events, and Assisted Telephony.
- Before releasing objects after this result, retain provider identity, object generation, current state, requested transition, and the event sequence surrounding requesting information or control that applies only to a call currently selected in a phone or UI context.
When the application constructed the selected call, it usually calls for caller-side validation. When enumeration or an event supplied it, it more often points to stale lifetime, provider replacement, device removal, configuration drift, or cross-session reuse. The ownership distinction for this HRESULT prevents a broad repair from masking the real defect.
Root-cause hypotheses
- It can also indicate that the selected call belonged to another address, call, device, provider generation, user session, or COM object.
- An asynchronous event can produce it when removal, disconnect, cancellation, reinitialization, or a state transition occurs after validation.
- A wrapper can trigger it by converting an enumeration, identifier, duration, structure size, encoding, or ownership rule incorrectly.
- It can occur when the caller supplies a malformed, unsupported, stale, or out-of-scope selected call.
Choose among those branches only after comparing the failed selected call with live capabilities or objects obtained from the same provider generation. A well-formed value can still be invalid because its scope, owner, state, or lifetime no longer matches the operation.
Diagnostic record
- Record it, 0X80040054, the native method, operation ID, elapsed time, process and thread IDs, application build, architecture, and COM apartment.
- capture call ID, selected-call collection, phone or address context, selection event, current call state, and UI generation.
- Keep provider version, address/call/phone/terminal identities, current state, requested state, object generation, and the first lower-level error that preceded it.
- Redact telephone numbers, credentials, recordings, user-user data, and directory attributes from it telemetry while retaining lengths, types, hashes, ranges, capability flags, and opaque correlation identifiers.
A useful incident can answer whether the selected call came from configuration, enumeration, user input, cached state, or a provider callback. The result record should also show whether the operation succeeds with a newly enumerated object or freshly validated value.
Investigation order
- Capture it at the first native return and identify the exact method used for requesting information or control that applies only to a call currently selected in a phone or UI context.
- Enumerate current provider capabilities or objects and compare them with the selected call rejected by it.
- Validate the selected call without silently correcting it; check type, size, range, encoding, identifier scope, ownership, and lifetime as applicable.
- Reconstruct the event timeline before it to find removal, disconnect, cancellation, service restart, provider reinitialization, or another state transition.
- Reproduce it with one object and one operation, then vary only the suspected field or state while tracking partial output and side effects.
Recovery conditions
The evidence-based correction for this HRESULT is to select the intended live call explicitly and clear selection when the call ends. After it follows a provider, device, service, or configuration change, obtain a fresh object because an old interface or opaque identifier may remain invalid after recovery.
Treat it retry policy as part of the owning operation rather than a property of the hexadecimal value alone. User-visible handling of it should describe the actionable condition—invalid data, wrong state, missing resource, unavailable service, or policy refusal—rather than displaying only the HRESULT.
Failure example
For example, a phone UI keeps focus on a completed call and a button command is rejected until the active call is selected The application should log the failed selected call, provider and object generation, native method, and state-changing event, then verify recovery with a newly obtained object instead of reusing the instance that returned it.
Nearby constants
TAPI_E_INVALIDSTREAM concerns a media stream object; it concerns call selection state Keep that distinction when building dashboards and exception mappings for this HRESULT; otherwise input defects, lifecycle races, capacity limits, service outages, and final call outcomes collapse into one misleading category.
Implementation guidance
Operational repair for this HRESULT should target only the component identified by evidence: the Telephony service, service provider, COM server, device, configuration record, application package, or remote system. Copying arbitrary DLLs or broadly deleting registration data can create additional failures without correcting the original selected call.
References
- Microsoft: TAPI_E constants — official Microsoft documentation used to interpret it.
- Microsoft: ITCallInfo
- Microsoft: TAPI 3.1 Reference
- Microsoft: Telephony API interfaces
Looking for a different code? Search another status or error code.