What does HRESULT 0xC00D1B8C (NS_E_NO_REALTIME_PREPROCESS) mean?

Status / error code:

Category:

Constant name:

Source:

Facility:

Operating System:

Description:

It is not possible to use image preprocessing with live encoding.%0

Previous	Next
NS_E_WME_VERSION_MISMATCH	NS_E_NO_REPEAT_PREPROCESS

NS_E_NO_REALTIME_PREPROCESS

How to interpret the code in a real encoding session

0xC00D1B8C is named NS_E_NO_REALTIME_PREPROCESS. Its practical scope is image preprocessing requested for a live source that cannot complete the required look-ahead or reread, which belongs to preprocessing, analysis and multipass constraints rather than to every part of Windows Media playback or Windows itself.

Mechanism and point of failure

Inverse telecine, time compression, image preprocessing, content analysis and two-pass encoding require access to particular source types and often require rereading or temporarily storing the source in a session that returns this result. Live, looping and device inputs impose additional restrictions.

The underlying audio or video source may be healthy while the requested preprocessing workflow is impossible for that source lifecycle in a session that returns this result. A typical reproduction is: a live broadcast preset enables a filter intended for offline preprocessing. This makes the first result from the Encoder more valuable than a later generic message.

Reproduction matrix

Field	What to preserve
Decisive values	source live/file status, enabled preprocessing filter and selected codec pass mode
Producing object	source type, live/file flag, Repeat flag, pass count, temporary-storage setting, preprocessing filters, analyzer frame count, input frame rate, content EDL path and selected codec mode
Session correlation	the same source-group generation, audience index, object identity and callback sequence that produced this result
Lower-level evidence	the first COM, driver, file-system or codec HRESULT observed before the Encoder mapped the condition to this result
Controlled comparison	a known-good session that changes only the setting named in the no realtime preprocess boundary

Evidence matrix

Observation	How to interpret it
Observation that supports it	The decisive evidence is source live/file status, enabled preprocessing filter and selected codec pass mode. It confirms image preprocessing requested for a live source that cannot complete the required look-ahead or reread in the same object generation.
Observation that points to an earlier failure	The recorded values satisfy the no realtime preprocess rule, but a source, driver, COM activation or file operation returns a different HRESULT first.
Observation that points to a later failure	The Encoder passes this boundary (image preprocessing requested for a live source that cannot complete the required look-ahead or reread), but a codec, archive or broadcast sink then fails in a subsequent stage.
Verification after correction	Apply this isolated change: disable the incompatible preprocessing step or encode from a file source. The original no realtime preprocess call should then advance past the same checkpoint.

The operational impact of it is limited to the preprocessing, analysis and multipass constraints transition that owns image preprocessing requested for a live source that cannot complete the required look-ahead or reread. In the representative case where a live broadcast preset enables a filter intended for offline preprocessing, keep the first failing call and its object identity so a later wrapper cannot replace the no realtime preprocess evidence.

Minimal experiment

Record 0xC00D1B8C, it, the Encoder version and the exact API call or property access that returned it.
Export the current .wme or .prx configuration, then capture source live/file status, enabled preprocessing filter and selected codec pass mode.
verify the preprocessing, analysis and multipass constraints precondition without changing the source, profile and output sink at the same time.
Run one controlled comparison in which only this condition changes: disable the incompatible preprocessing step or encode from a file source.
After the change, recreate the affected Encoder object rather than assuming the existing graph discarded its earlier no realtime preprocess state.

Do not collapse these results together

Result	Why it is a different boundary
`NS_E_NO_REALTIME_TIMECOMPRESSION`	time-compression setup on a live broadcast that cannot be reread or scheduled faster than real time
`NS_E_NO_REPEAT_PREPROCESS`	preprocessing or two-pass analysis requested while the source is configured to loop
`NS_E_INVALIDINPUTFPS`	inverse-telecine validation requiring the expected 30-fps input cadence

What to change—and what to leave alone

Change the smallest responsible precondition: disable the incompatible preprocessing step or encode from a file source. While retesting it, keep all unrelated source, audience and output values fixed until the same call is repeated.

Do not enable several preprocessing features at once during diagnosis; validate the plain one-pass source first, then add one transformation with its required storage or analysis stage in a session that returns it.

Authoritative documentation

Looking for a different code? Search another status or error code.